WATER POLLUTION AND SOCIETY

David Krantz and Brad Kifferstein

INTRODUCTION

Comprising over 70% of the Earth�s surface, water is undoubtedly the most precious natural resource that exists on our planet. Without the seemingly invaluable compound comprised of hydrogen and oxygen, life on Earth would be non-existent: it is essential for everything on our planet to grow and prosper. Although we as humans recognize this fact, we disregard it by polluting our rivers, lakes, and oceans. Subsequently, we are slowly but surely harming our planet to the point where organisms
are dying at a very alarming rate. In addition to innocent organisms dying off, our drinking water has become greatly affected as is our ability to use water for recreational purposes. In order to combat water pollution, we must understand the problems and become part of the solution.

POINT AND NONPOINT SOURCES

According to the American College Dictionary, pollution is defined as: �to make foul or unclean; dirty.� Water pollution occurs when a body of water is adversely affected due to the addition of large amounts of materials to the water. When it is unfit for its intended use, water is considered polluted. Two types of water pollutants exist; point source and nonpoint source. Point sources of pollution occur when harmful substances are emitted directly into a body of water. The Exxon Valdez oil spill best illustrates a point source water pollution. A nonpoint source delivers pollutants indirectly through environmental changes. An example of this type of water pollution is when fertilizer from a field is carried into a stream by rain, in the form of run-off
which in turn effects aquatic life. The technology exists for point sources of pollution to be monitored and regulated, although political factors may complicate matters. Nonpoint sources are much more difficult to control. Pollution arising from nonpoint
sources accounts for a majority of the contaminants in streams and lakes.

CAUSES OF POLLUTION

Many causes of pollution including sewage and fertilizers contain nutrients such as nitrates and phosphates. In excess levels, nutrients over stimulate the growth of aquatic plants and algae. Excessive growth of these types of organisms consequently clogs our waterways, use up dissolved oxygen as they decompose, and block light to deeper waters.
This, in turn, proves very harmful to aquatic organisms as it affects the respiration ability or fish and other invertebrates that reside in water.
Pollution is also caused when silt and other suspended solids, such as soil, washoff plowed fields, construction and logging sites, urban areas, and eroded river banks when it rains. Under natural conditions, lakes, rivers, and other water bodies undergo Eutrophication, an aging process that slowly fills in the water body with sediment and organic matter. When these sediments enter various bodies of water, fish respirationbecomes impaired, plant productivity and water depth become reduced, and aquatic organisms and their environments become suffocated. Pollution in the form of organic
material enters waterways in many different forms as sewage, as leaves and grass clippings, or as runoff from livestock feedlots and pastures. When natural bacteria and protozoan in the water break down this organic material, they begin to use up the oxygen dissolved in the water. Many types of fish and bottom-dwelling animals cannot survive when levels of dissolved oxygen drop below two to five parts per million. When this occurs, it kills aquatic organisms in large numbers which leads to disruptions in the food chain.
Polluted River in the United Kingdom
The pollution of rivers and streams with chemical contaminants has become one of the most crutial environmental problems within the 20th century. Waterborne chemical pollution entering rivers and streams cause tramendous amounts of destruction.

Pathogens are another type of pollution that prove very harmful. They can cause many illnesses that range from typhoid and dysentery to minor respiratory and skin diseases. Pathogens include such organisms as bacteria, viruses, and protozoan. These pollutants enter waterways through untreated sewage, storm drains, septic tanks, runoff from farms, and particularly boats that dump sewage. Though microscopic, these pollutants have a tremendous effect evidenced by their ability to cause sickness.

ADDITIONAL FORMS OF WATER POLLUTION

Three last forms of water pollution exist in the forms of petroleum, radioactive substances, and heat. Petroleum often pollutes waterbodies in the form of oil, resulting from oil spills. The previously mentioned Exxon Valdez is an example of this type of water pollution. These large-scale accidental discharges of petroleum are an important cause of pollution along shore lines. Besides the supertankers, off-shore drilling operations contribute a large share of pollution. One estimate is that one ton of oil is spilled for every million tons of oil transported. This is equal to about 0.0001 percent. Radioactive substances are produced in the form of waste from nuclear power plants, and from the industrial, medical, and scientific use of radioactive materials. Specific forms of waste are uranium and thorium mining and refining. The last form of water pollution is heat. Heat is a pollutant because increased temperatures result in the deaths of many aquatic organisms. These decreases in temperatures are caused when a discharge of cooling water by factories and power plants occurs.
Demonstrators Protest Drilling
Oil pollution is a growing problem, particularly devestating to coastal wildlife. Small quantities of oil spread rapidly across long distances to form deadly oil slicks. In this picture, demonstrators with “oil-covered” plastic animals protest a potential drilling project in Key Largo, Florida. Whether or not accidental spills occur during the project, its impact on the delicate marine ecosystem of the coral reefs could be devastating.

Oil Spill Clean-up
Workers use special nets to clean up a California beach after an oil tanker spill. Tanker spills are an increasing environmental problem because once oil has spilled, it is virtually impossible to completely remove or contain it. Even small amounts spread rapidly across large areas of water. Because oil and water do not mix, the oil floats on the water and then washes up on broad expanses of shoreline. Attempts to chemically treat or sink the oil may further disrupt marine and beach ecosystems.

CLASSIFYING WATER POLLUTION

The major sources of water pollution can be classified as municipal, industrial, and agricultural. Municipal water pollution consists of waste water from homes and commercial establishments. For many years, the main goal of treating municipal
wastewater was simply to reduce its content of suspended solids, oxygen-demanding materials, dissolved inorganic compounds, and harmful bacteria. In recent years, however, more stress has been placed on improving means of disposal of the solid residues from the municipal treatment processes. The basic methods of treating municipal wastewater fall into three stages: primary treatment, including grit removal, screening, grinding, and sedimentation; secondary treatment, which entails oxidation of dissolved organic matter by means of using biologically active sludge, which is then filtered off; and tertiary treatment, in which advanced biological methods of nitrogen removal and chemical and physical methods such as granular filtration and activated carbon absorption are employed. The handling and disposal of solid residues can
account for 25 to 50 percent of the capital and operational costs of a treatment plant. The characteristics of industrial waste waters can differ considerably both within and among industries. The impact of industrial discharges depends not only on their
collective characteristics, such as biochemical oxygen demand and the amount of suspended solids, but also on their content of specific inorganic and organic substances. Three options are available in controlling industrial wastewater. Control can take place at the point of generation in the plant; wastewater can be pretreated for discharge to municipal treatment sources; or wastewater can be treated completely at the plant and either reused or discharged directly into receiving waters.
Wastewater Treatment
Raw sewage includes waste from sinks, toilets, and industrial processes. Treatment of the sewage is required before it can be safely buried, used, or released back into local water systems. In a treatment plant, the waste is passed through a series of screens, chambers, and chemical processes to reduce its bulk and toxicity. The three general phases of treatment are primary, secondary, and tertiary. During primary treatment, a large percentage of the suspended solids and inorganic material is removed from the sewage. The focus of secondary treatment is reducing organic material by accelerating natural biological processes. Tertiary treatment is necessary when the water will be reused; 99 percent of solids are removed and various chemical processes are used to ensure the water is as free from impurity as possible.

Agriculture, including commercial livestock and poultry farming, is the source of many organic and inorganic pollutants in surface waters and groundwater. These contaminants include both sediment from erosion cropland and compounds of
phosphorus and nitrogen that partly originate in animal wastes and commercial fertilizers. Animal wastes are high in oxygen demanding material, nitrogen and phosphorus, and they often harbor pathogenic organisms. Wastes from commercial
feeders are contained and disposed of on land; their main threat to natural waters, therefore, is from runoff and leaching. Control may involve settling basins for liquids, limited biological treatment in aerobic or anaerobic lagoons, and a variety of other methods.

GROUND WATER

Ninety-five percent of all fresh water on earth is ground water. Ground water is found in natural rock formations. These formations, called aquifers, are a vital natural resource with many uses. Nationally, 53% of the population relies on ground water as a source of drinking water. In rural areas this figure is even higher. Eighty one percent of community water is dependent on ground water. Although the 1992 Section 305(b) State Water Quality Reports indicate that, overall, the Nation�s ground water quality is good to excellent, many local areas have experienced significant ground water contamination.
Some examples are leaking underground storage tanks and municipal landfills.

LEGISLATION

Several forms of legislation have been passed in recent decades to try to control water pollution. In 1970, the Clean Water Act provided 50 billion dollars to cities and states to build wastewater facilities. This has helped control surface water pollution from industrial and municipal sources throughout the United States. When congress passed the Clean Water Act in 1972, states were given primary authority to set their own standards for their water. In addition to these standards, the act required that all state beneficial uses and their criteria must comply with the �fishable and swimmable� goals of the act. This essentially means that state beneficial uses must be able to support aquatic life and recreational use. Because it is impossible to test water for every type of disease-causing organism, states usually look to identify indicator bacteria. One for a example is a bacteria known as fecal coliforms.(Figure 1 shows the quality of water for each every state in the United States, click on the US link). These indicator bacteria suggest that a certain selection of water may be contaminated with untreated sewage and that other, more dangerous, organisms are present. These legislations are an important part in the fight against water pollution. They are useful in preventing Envioronmental catastrophes. The graph shows reported pollution incidents since 1989-1994. If stronger legislations existed, perhaps these events would never have occurred.

GLOBAL WATER POLLUTION

Estimates suggest that nearly 1.5 billion people lack safe drinking water and that at least 5 million deaths per year can be attributed to waterborne diseases. With over 70 percent of the planet covered by oceans, people have long acted as if these very bodies of water could serve as a limitless dumping ground for wastes. Raw sewage, garbage, and oil spills have begun to overwhelm the diluting capabilities of the oceans, and most coastal waters are now polluted. Beaches around the world are closed regularly, often because of high amounts of bacteria from sewage disposal, and marine wildlife is beginning to suffer.
Perhaps the biggest reason for developing a worldwide effort to monitor and restrict global pollution is the fact that most forms of pollution do not respect national boundaries. The first major international conference on environmental issues was held
in Stockholm, Sweden, in 1972 and was sponsored by the United Nations (UN). This meeting, at which the United States took a leading role, was controversial because many developing countries were fearful that a focus on environmental protection was a means for the developed world to keep the undeveloped world in an economically subservient position. The most important outcome of the conference was the creation of the United Nations Environmental Program (UNEP).

UNEP was designed to be �the environmental conscience of the United Nations,� and, in an attempt to allay fears of the developing world, it became the first UN agency to be headquartered in a developing country, with offices in Nairobi, Kenya. In addition to attempting to achieve scientific consensus about major environmental issues, a major focus for UNEP has been the study of ways to encourage sustainable development increasing standards of living without destroying the environment. At the time of UNEP’s creation in 1972, only 11 countries had environmental agencies. Ten years later that number had grown to 106, of which 70 were in developing countries.

WATER QUALITY

Water quality is closely linked to water use and to the state of economic development. In industrialized countries, bacterial contamination of surface water caused serious health problems in major cities throughout the mid 1800�s. By the turn of the century, cities in Europe and North America began building sewer networks to route domestic wastes downstream of water intakes. Development of these sewage networks and waste treatment facilities in urban areas has expanded tremendously in the past two decades. However, the rapid growth of the urban population (especially in Latin America and Asia) has outpaced the ability of governments to expand sewage and water infrastructure. While waterborne diseases have been eliminated in the developed world, outbreaks of cholera and other similar diseases still occur with alarming frequency in the developing countries. Since World War II and the birth of the �chemical age�, water quality has been heavily impacted worldwide by industrial and agricultural chemicals. Eutrophication of surface waters from human and agricultural wastes and nitrification of groundwater from agricultural practices has greatly affected large parts of the world. Acidification of surface waters by air pollution is a recent phenomenon and threatens aquatic life in many area of the world. In developed countries, these general types of pollution have occurred sequentially with the result that most developed countries have successfully dealt with major surface water pollution. In contrast, however, newly industrialized countries such as China, India, Thailand, Brazil, and Mexico are now facing all these issues simultaneously.

CONCLUSION

Clearly, the problems associated with water pollution have the capabilities to disrupt life on our planet to a great extent. Congress has passed laws to try to combat water pollution thus acknowledging the fact that water pollution is, indeed, a seriousissue. But the government alone cannot solve the entire problem. It is ultimately up to us, to be informed, responsible and involved when it comes to the problems we face with our water. We must become familiar with our local water resources and learn about ways for disposing harmful household wastes so they don�t end up in sewage treatment plants that can�t handle them or landfills not designed to receive hazardous materials. In our yards, we must determine whether additional nutrients are needed before fertilizers are applied, and look for alternatives where fertilizers might run off into surface waters. We have to preserve existing trees and plant new trees and shrubs to help prevent soil erosion and promote infiltration of water into the soil. Around our houses, we must keep litter, pet waste, leaves, and grass clippings out of gutters and storm drains. These are
just a few of the many ways in which we, as humans, have the ability to combat water pollution. As we head into the 21st century, awareness and education will most assuredly continue to be the two most important ways to prevent water pollution. If these measures are not taken and water pollution continues, life on earth will suffer severely.
Global environmental collapse is not inevitable. But the developed world must work with the developing world to ensure that new industrialized economies do not add to the world’s environmental problems. Politicians must think of sustainable development rather than economic expansion. Conservation strategies have to become more widely accepted, and people must learn that energy use can be dramatically diminished without sacrificing comfort. In short, with the technology that currently
exists, the years of global environmental mistreatment can begin to be reversed.

Important Terms

Aquifers - natural rock formations, which contain ground water.
Eutrophication - The process of slowly filling in a water body with sediments and organic matter.
Non point source - delivers pollutants indirectly through environmental changes. One way in, which this occurs, is through run-off.
Pathogens - or disease producing organism.
Point source - occurs when harmful substances are emitted directly into a body of water. One way in which this occurs, is when someone throws a coke can into a body of water.
Pollution - to make foul or unclean; dirty.
Sediments - minerals or organic matter deposited by water, air, or ice…matter which settles to the bottom a liquid.

http://www.umich.edu/~gs265/society/waterpollution.htm

Published in: on March 13, 2008 at 11:30 pm Comments (1)

Monitoring Asia-Pacific Disasters From Space

Canberra, Australia (SPX) Feb 25, 2008 - A space-based international Earth observation network to detect and monitor natural disasters in the Asia-Pacific region has been formed with a substantial contribution from Australian science.

Called Sentinel Asia, the network of information-delivery websites has its roots in the Australian bushfire tracking system, Sentinel Hotspots, which was developed in 2002 by CSIRO, Geoscience Australia and the Australian Defence Imagery and Geospatial Organisation.

“This will be a critical information delivery system on wildfires, flooding, drought, and landslides in our region, where those events can be seen by Earth observing satellites in real time,” says the coordinator of Australia’s input, senior CSIRO Marine and Atmospheric Research scientist Dr Alex Held.

“Australia has had a pivotal, strategic role in developing the system which has the potential to benefit billions of people in our region by assisting authorities in a recovery response,” he said.

“The concept of Sentinel Asia is to provide online information from Earth observation satellites in ‘near real-time’ through a network of webGIS services such as the Australian Sentinel Hotspots system.”

Initially supported by the Japanese Government through the Japan Aerospace Exploration Agency (JAXA), Sentinel Asia aims to show the value of Earth observation data for disaster management in the region. The system has been activated 10 times by seven countries including Australia in the last 12 months, mostly in response to earthquakes and floods.

Planned improvements include further nodes in other countries, use of high bandwidth communications satellites to provide information more quickly, and access to a wider range of Earth observation satellites.

Dr Held said many of the causes and impacts of natural disasters, including droughts, are observable, often in real-time, from space by orbiting or geostationary Earth observing systems.

“When efficiently combined with modern information-distribution methods, this data can be sent rapidly to affected communities and local emergency agencies in some cases as early-warning before the disaster occurs, or as post-disaster maps, to assist in recovery operations,” he said.

The system largely uses free-to-air satellite imagery produced by Earth-observing satellites operated by the US, Europe, Japan, India and, in the future, other countries in Australasia which are planning satellite launches.

Source : http://www.terradaily.com/

Published in: on at 11:15 pm Comments (0)

Radar Satellite Provides Clear View Of Traffic Even In Dark And Fog

Bonn, Germany (SPX) Mar 06, 2008 - The German Aerospace Center (DLR) has begun several months of tests into the feasibility of obtaining traffic information via satellite. The German radar satellite TerraSAR-X is going to monitor selected sections of motorway in Germany, Austria, Switzerland and California.
The aim of this project is to develop a procedure for large-scale traffic data capture, independent of ground systems, that permits data relay to various traffic information providers. In contrast to measurement procedures used to date, most of them stationary cameras, information gleaned by satellite can yield up-to-the-minute information, even from roads without sensors, whatever the weather, regardless of borders.

The technology is not limited to discovering areas of high traffic density. It can also be used to calculate the average speed of motorway (autobahn) traffic, so that the exact journey time between junctions can be established. With the help of such information, traffic information service providers will be able to make better journey time forecasts - even in fog, heavy rain and darkness - thanks to the latest radar technology.

In the context of the field campaign started on 26 February 2008, the first stretches of motorway to be observed will be the A4 to the west of Dresden, and the area where Germany, Austria and Switzerland meet. Later, this will be extended to the Ruhr, the A5 and A8 at Karlsruhe and Interstate 5 in California, to the north-west of Los Angeles.

Traffic data capture represents an expansion of the capabilities of the radar satellite. TerraSAR-X, which has been operational since June 2007, has sent over 10 000 high-quality radar images back to Earth to date.

In order to analyse the large amounts of data, an additional mainframe computer was made available at the DFD field station at Neustrelitz, near Berlin, in January 2008. The surveying, and the preparation of the data for the emergency services are just two further examples of potential varied uses of the satellite data, which is already being used by over 200 scientists world-wide.

TerraSAR-X
TerraSAR-X is the first German satellite to be manufactured under what is called a public-private partnership (PPP) between the German Aerospace Center and Astrium GmbH in Friedrichshafen.

The satellite circles Earth in a polar orbit and records unique, high-quality X-band radar data of the whole planet with its active antenna. TerraSAR-X works regardless of weather conditions, cloud cover and daylight and is able to provide radar data with a resolution of up to one metre.

DLR is responsible for using TerraSAR-X data for scientific purposes. It is also responsible for planning and implementing the mission as well as controlling the satellite. Astrium built the satellite and shares the costs for developing and using it. Die Infoterra GmbH, a subsidiary company founded specifically for this purpose by Astrium, is responsible for marketing the data commercially.

Source : http://www.spacemart.com/

Published in: on at 11:13 pm Comments (0)

UK’s Traffic Management Act demands all road-works to be recorded - GIS a solution

Utility companies and local authorities, equipped with Ordnance Survey�s most detailed mapping data, are transforming the management and coordination of street works in England.

New Traffic Management Act (TMA) legislation, due in April this year, declares that all road and street-works activities in England and Wales should be recorded. Utility companies must also provide local authorities with coordinates showing where work is to be carried out. Such additional spatial information is crucial � from helping to fulfil network management duties to ensuring a smoother coordination of works. And the process is also set to help reduce disruption for the travelling public.

A system, trialled by National Grid, Thames Water and London Borough of Camden, is launched by Symology this week. Insight 2.5 has Ordnance Survey�s OS MasterMap data at its heart. It allows utilities and highways authorities to record notices of intended works � and send them to one another electronically.

“Those using the system will get a new perspective of works, where they are planned and how they are progressing,” says Scott Hutchinson of Symology. “It should make the task of providing publicly accessible geographic information a whole lot easier.”

“We�ve completely redesigned our systems to fully meet the demands of the TMA era,� he says. “And, to have OS MasterMap as a core component of Insight 2.5 ensures that works promoters can accurately plot their works on the map � and send accurate coordinate information. The system also benefits local authority traffic managers because they can view all on going works and potential conflicts.”

“It is great to see OS MasterMap data being used in innovative and really beneficial ways throughout utility organisations. Symology�s Insight 2.5 system allows users to have comprehensive coverage of the entire street works noticing lifecycle at any time and any place,” says Ordnance Survey�s Marc Hobell. “All this is underpinned by OS MasterMap Topography and Integrated Transport Network (ITN) Layers, which only go to demonstrate, once again, the power of using intelligent geographic information.”

Source : http://www.publictechnology.net/

Published in: on at 11:03 pm Comments (0)

History of GPS

In the 1991 the USA opened to the world the service with name SPS (Standard Positioning System), with detailed lists differentiated that called soldier PPS (Precision Positioning System). In practical it came introduced the so-called Selective Availability (KNOWS) that it introduced intentional errors in marks them satellitari in order to reduce the accuracy of the survey, concurring precisions single in the order of 100-150 m.

The GPS has been created in substitution of the previous system, the Transit, when the USA, rinunciando to the Selective Availability, have rendered the first one taken care of how much the second, supporting it with a net of 24 satellites crafts them.

The degradation of marks them has been disabilitata from the month of May 2000, thanks to a decree of the President of the United States Bill Clinton, putting therefore to disposition the precision puts into effect them of approximately 10-20 m. In the models for civil use a device is present that inhibits the operation to heights and advanced speeds to sure values, in order to prevent of the assembly on unexpected missiles.

The UE has in plan the completion of an own net of satellites, Sistema of Galileo positioning, for civil scopes, between which the GPS. This plan has an obvious strategic valence in how much the net American is property of the single United states and is managed military authorities, than, in particular conditions, they could decide discretionarily and unilaterally to reduce the precision or block the access selective to the system; the sharing of the investment and the property from part of the utilizzatori states guarantees continuity, accessibility and interoperabilità of the service.
Source:http://tomtomguide.blogspot.com

Published in: on at 10:54 am Comments (0)

Archaeological Remote Sensing

Now more than ever, archeological research is interdisciplinary: botany, forestry, soil science, hydrology - all of which contribute to a more complete understanding of the earth, climate shifts, and how people adapt to large regions.

As a species, we’ve been literally blind to the universe around us. If the known electromagnetic spectrum were scaled up to stretch around the Earth’s circumference, the human eye would see a portion equal to the diameter of a pencil. Our ability to build detectors that see for us where we can’t see, and computers that bring the invisible information back to our eyesight, will ultimately contribute to our survival on Earth and in space.

The spectrum of sunlight reflected by the Earth’s surface contains information about the composition of the surface, and it may reveal traces of past human activities, such as agriculture. Since sand, cultivated soil, vegetation, and all kinds of rocks each have distinctive temperatures and emit heat at different rates, sensors can “see” things beyond ordinary vision or cameras. Differences in soil texture are revealed by fractional temperature variations. So it is possible to identify loose soil that had been prehistoric agricultural fields, or was covering buried remains. The Maya causeway was detected through emissions of infrared radiation at a different wavelength from surrounding vegetation. More advanced versions of such multi-spectral scanners (Visible & IR) can detect irrigation ditches filled with sediment because they hold more moisture and thus have a temperature different from other soil. The ground above a buried stone wall, for instance, may be a touch hotter than the surrounding terrain because the stone absorbs more heat. Radar can penetrate darkness, cloud cover, thick jungle canopies, and even the ground.

Remote sensing can be a discovery technique, since the computer can be programmed to look for distinctive “signatures” of energy emitted by a known site or feature in areas where surveys have not been conducted. Such “signatures” serve as recognition features or fingerprints. Such characteristics as elevation, distance from water, distance between sites or cities, corridors, and transportation routes can help to predict the location of potential archeological sites.
Computational techniques used to analyze data.

1. sun-angle correction
2. density slicing
3. band ratioing
4. edge enhancement
5. synthetic color assignment
6. filtering
7. multichannel analysis
Remote Sensing Instruments

Aerial Photography:
Many features which are difficult or impossible to see standing on the ground become very clear when seen from the air. But, black and white photography only records about twenty-two perceptible shades of gray in the visible spectrum. Also, optical sources have certain liabilities, they must operate in daylight, during clear weather, on days with minimal atmospheric haze.

Color Infrared Film (CIR):
Detects longer wavelengths somewhat beyond the red end of the light spectrum. CIR film was initially employed during World War II to differentiate objects that had been artificially camouflaged. Infrared photography has the same problems that conventional photography has, you need light and clear skies. Even so, CIR is sensitive to very slight differences in vegetation. Because buried archeological features can affect how plants grow above them, such features become visible in color infrared photography.

Thermal Infrared Multispectral Scanner (TIMS):
A six channel scanner that measures the thermal radiation given off by the ground, with accuracy to 0.1 degree centigrade. The pixel (picture element) is the square area being sensed, and the size of the pixel is directly proportional to sensor height. For example, pixels from Landsat satellites are about 100 feet (30 m) on a side, and thus have limited archeological applications. However, pixels in TIMS data measure only a few feet on a side and as such can be used for archeological research. TIMS data were used to detect ancient Anasazi roads in Chaco Canyon, NM.

Airborne Oceanographic Lidar (ADI):
A laser device that makes “profiles” of the earth’s surface. The laser beam pulses to the ground 400 times per second, striking the surface every three and a half inches, and bounces back to its source. In most cases, the beam bounces off the top of the vegetation cover and off the ground surface; the difference between the two give information on forest height, or even the height of grass in pastures. As the lidar passes over an eroded footpath that still affects the topography, the pathway’s indentation is recorded by the laser beam. The lidar data can be processed to reveal tree height as well as elevation, slope, aspect, and slope length of ground features. Lidar can also be used to penetrate water to measure the morphology of coastal water, detect oil forms, fluorescent dye traces, water clarity, and organic pigments including chlorophyll. In this case, part of the pulse is reflected off the water surface, while the rest travels to the water bottom and is reflected. The time elapsed between the received impulses allows for a determination of water depth and subsurface topography.

Synthetic Aperture Radar (SAR):
SAR beams energy waves to the ground and records the energy reflected. Radar is sensitive to linear and geometric features on the ground, particularly when different radar wavelengths and different combinations of the horizontal and vertical data are employed. Different wavelengths are sensitive to vegetation or to ground surface phenomena. In dry, porous soils, radar can penetrate the surface. In 1982, radar from the space shuttle penetrated the sand of the Sudanese desert and revealed ancient watercourses. Using airborne radar in Costa Rica, prehistoric footpaths have been found.

Microwave Radar:
Beaming radar pulses into the ground and measuring the echo is a good way of finding buried artifacts in arid regions (water absorbs microwaves). Man-made objects tend to reflect the microwaves, giving one a “picture” of what is underground without disturbing the site.

Selected Papers

“Remote Sensing Methods,” In Advances in Science and Technology for Historic Preservation, edited by Ray Williamson. Plenum Press. (In Press).

“Remote Sensing,” In American Journal of Archeology, 99:83-84, 1995.

“Applications of Ecological Concepts and Remote Sensing Technologies in Archeological Site Reconnaissance,” with F. Miller and D. Lee. (In Applications of Space-Age Technology in Anthropology, edited by Clifford Behrens and Thomas Sever. NASA, Stennis Space Center, MS, 1991.)

“Remote Sensing,” Chapter 14 of Benchmarks In Time and Culture: Introductory Essays in the Methodology of Syro-Palestinian Archeology. Scholars Press. March, 1988.

“Cultural and Ecological Applications of Remote Sensing.” Final Report of a Conference Sponsored by the National Science Foundation. With Daniel Gross and Paul Shankman. University of Boulder Colorado, Boulder. April, 1988.

“Conference on Remote Sensing: Potential for the Future.” NASA, Stennis Space Center, Science and Technology Laboratory, SSC, MS., January, 1985.

Responsible Official: Dr. William M. Lapenta (bill.lapenta@nasa.gov)
Page Author: Tom Sever
Page Curator: Diane Samuelson (diane.samuelson@msfc.nasa.gov)
source:

http://www.ghcc.msfc.nasa.gov/archeology/remote_sensing.html

Published in: on at 12:55 am Comments (1)

Why are map projections an issue in GIS?

n many respects, GIS has freed us from the constraints of modelling the spatial relationships using a drawing on paper. For example:

* Easy customizing of what features are displayed and how they look.

* attachment of database attributes to features.

* easier filing.

* quick creation of buffers.

* overlays and area calculations.

However, the spatial representation of data in GIS remains tied to a mapping plane. Map projections are the means of representing an ellipsoidal Earth on a mapping plane. Area calculations are done on the mapping plane, not on the ellipsoid

By definition, topological relationships are not affected by projection transformations. However, areas, shapes, angles and distances are affected.

Map projection characteristics
Different map projections retain or distort the following quantities. It is not possible for any one projection to retain more than one of them over a large area of the earth.

* area: equal-area means that a spatial unit on one part of the map covers exactly an equal area of the actual Earth as a spatial unit of the same size in any other part of the map

* shape: conformal projections preserve the relative local angles about every point on the map, so that meridians intersect parallels at 90 degrees; no map can be both equal-area and conformal

* scale: no map projection shows scale correctly throughout the entire map; equidistant projections show true scale between one or two points and every other point on the map, or along every meridian

* direction: azimuthal projections show correctly the directions from all points on the map to the centre

Common projections
Some of the common projections in use are:

* Universal Transverse Mercator (UTM): conformal, best for north south extents; scale is true along the two meridians halfway between the Central Meridian and the edge of the zone (too small between these lines and too large outside of these lines); standard projection for basemapping and thematic mapping in BC; BCE regions extend across more than one UTM zone preventing the construction of a seamless GIS database

* Polyconic: preserves area, shape, distance and azimuth for small area s; best for north-south extents; scale increases away from the central meridian; used for the 1:2 Million map of BC (CM of 129:00:00 W used for source paper map so that province would sit straight up and down on sheet); generally considered that the scale distortion is acceptable only up to 9 degrees away from the Central Meridian; BC spans 115:00:00 W to 140:00:00 W which is 12 1/2 degrees on either side of the Central Meridian; former projection for US topographic maps of 1 degree extent, but not recommended for larger areas because of distortion

* Lambert Conformal Conic: conformal, best for east-west extents away from the equator; used in National Atlas of Canada and for Agriculture Canada 1:1 Million soil maps; US state basemaps; scale is too small between standard parallels and too large beyond them

* Albers Equal-Area Conic: equal-area, best for east-west extents away from the equator; scale is too small between standard parallels and too large beyond them; one of most commonly used projections for maps of conterminous USA

Published in: on at 12:30 am Comments (0)

International School on LiDAR Technology
IIT Kanpur
31March - 4April 2008
Organiser: Dr. Bharat Lohani
Contact: Department of Civil Engineering
IIT Kanpur
Kanpur 208 016, INDIA

Kanpur , UP
2008
Phone: +91-512-259 7413
Fax: +91-512-259 7395
Email: lidar08@iitk.ac.in
Website: http://home.iitk.ac.in/~blohani/LiDARSchool2008/index.html

Published in: on at 12:29 am Comments (0)

Why are map projections an issue in GIS?

In many respects, GIS has freed us from the constraints of modelling the spatial relationships using a drawing on paper. For example:

* Easy customizing of what features are displayed and how they look.

* attachment of database attributes to features.

* easier filing.

* quick creation of buffers.

* overlays and area calculations.

However, the spatial representation of data in GIS remains tied to a mapping plane. Map projections are the means of representing an ellipsoidal Earth on a mapping plane. Area calculations are done on the mapping plane, not on the ellipsoid

By definition, topological relationships are not affected by projection transformations. However, areas, shapes, angles and distances are affected.

Map projection characteristics
Different map projections retain or distort the following quantities. It is not possible for any one projection to retain more than one of them over a large area of the earth.

* area: equal-area means that a spatial unit on one part of the map covers exactly an equal area of the actual Earth as a spatial unit of the same size in any other part of the map

* shape: conformal projections preserve the relative local angles about every point on the map, so that meridians intersect parallels at 90 degrees; no map can be both equal-area and conformal

* scale: no map projection shows scale correctly throughout the entire map; equidistant projections show true scale between one or two points and every other point on the map, or along every meridian

* direction: azimuthal projections show correctly the directions from all points on the map to the centre

Common projections
Some of the common projections in use are:

* Universal Transverse Mercator (UTM): conformal, best for north south extents; scale is true along the two meridians halfway between the Central Meridian and the edge of the zone (too small between these lines and too large outside of these lines); standard projection for basemapping and thematic mapping in BC; BCE regions extend across more than one UTM zone preventing the construction of a seamless GIS database

* Polyconic: preserves area, shape, distance and azimuth for small area s; best for north-south extents; scale increases away from the central meridian; used for the 1:2 Million map of BC (CM of 129:00:00 W used for source paper map so that province would sit straight up and down on sheet); generally considered that the scale distortion is acceptable only up to 9 degrees away from the Central Meridian; BC spans 115:00:00 W to 140:00:00 W which is 12 1/2 degrees on either side of the Central Meridian; former projection for US topographic maps of 1 degree extent, but not recommended for larger areas because of distortion

* Lambert Conformal Conic: conformal, best for east-west extents away from the equator; used in National Atlas of Canada and for Agriculture Canada 1:1 Million soil maps; US state basemaps; scale is too small between standard parallels and too large beyond them

* Albers Equal-Area Conic: equal-area, best for east-west extents away from the equator; scale is too small between standard parallels and too large beyond them; one of most commonly used projections for maps of conterminous USA

full story:http://srmwww.gov.bc.ca/gis/projectiontutorial.html

Published in: on at 12:05 am Comments (0)